2,7kw @2Ohm Monoblock Ultimate T3 1000D

+A -A
Autor
Beitrag
baschdi85
Stammgast
#1 erstellt: 24. Feb 2008, 10:51
Also,..

verkaufe einen Insideramp aus USA / Canada..

Ultimate T3 1000D ,

http://ampguts.realmofexcursion.com/Ultimate_T3-1000D/

ist in einem neuwertigen Zustand,
hat richtig leistung, Zusatzbatt oder Kondensator sind hier Pflicht!

Bilder vom Orginalen Amp kann ich gerne zusenden..

VHB 400,- Euro

wenn interesse besteht: habe auch noch 2stck 4kanal amps aus der gleichen serie, falls jemand interesse an einheitlichen verstärkern hat.. T3-4075 mit 4x75wRMS/4ohm

Mfg
Sebastian
baschdi85
Stammgast
#2 erstellt: 26. Feb 2008, 18:41
dann gehen wir mal auf 390,- runter.....

Mfg
Baschdi
Deathwish
Stammgast
#3 erstellt: 26. Feb 2008, 19:33
wie spielt sie denn??? Mit ner analogen ala colossus zu vergleichen??
baschdi85
Stammgast
#4 erstellt: 27. Feb 2008, 16:37
kann ich leider keine vergleiche machen,..
hatte bis jetzt nur:

1x 12" Edge an Rockford bd500

2x15" Kicker S15L7 an GZ 2800X

2x12" Edge an GZ 2800X

2x12" Edge an Impact Agent D

2x12" Edge an Ultimate T3

von diesen Kombinationen fand ich die Ultimate an den 2stck 12"Edge am besten.
Meiner meinung nach hat sie die 2 woofer gut im griff,(DF)
kein nachschwingen etc bemerkbar, lautstärkemäßig ist sie deutlich lauter als die Ground zero und dabei auch irgendwie kontrollierter und stärker/härter ( schwer zu beschreiben)

eine andere Analoge stufe hatte ich noch nicht, nur die GZ 2800X, diese hatte auch mega strom gezogen..

die Ultimate betreibe ich jetzt seit ca. 6-8Monaten und bin am überlegen ob ich mir was kleineres einbaue ( kleinere woofer und kleinere endstufen...oder doch nicht..?)

ich würde ja sagen komm vorbei und höre sie probe..

wohne in 74076 Heilbronn

Mfg
Sebastian
Deathwish
Stammgast
#5 erstellt: 27. Feb 2008, 16:57
naja würd ich ja gerne, aber is doch nen bischen weit!
AmplicDizzorder
Ist häufiger hier
#6 erstellt: 02. Mrz 2008, 12:11
Ist die Stufe Ultimate T3-1000D denn noch zu haben?

lg Arta
baschdi85
Stammgast
#7 erstellt: 02. Mrz 2008, 19:58
ja, ist noch da,..

und auch noch 2stck 4-kanal verstärker aus der gleichen serie..(falls interesse besteht)

Mfg
Sebastian
AmplicDizzorder
Ist häufiger hier
#8 erstellt: 02. Mrz 2008, 20:40
Interesse hätte ich nur an der Großen

Stimmt der Preis noch? (390€)

Könnt mich bei dir melden, wenn du nen Messenger hast IcQ, etc...

lg Arta
baschdi85
Stammgast
#9 erstellt: 02. Mrz 2008, 20:48
habe keinen messenger oder ähnliches,

kannst aber auch unter

Baschdie85@aol.com

mir schreiben.

390 sind sogar noch VHB

Mfg
Sebastian
baschdi85
Stammgast
#10 erstellt: 04. Mrz 2008, 18:57
also,

ein paar interessenten sind am überlegen,..

Preis steht nun bei 345,- euro,..
wer für diesen preis als erstes zusagt bekommt sie..

versicherter Versand über DHL inklusive!

Mfg
Sebastian
Anabolic_Bass
Ist häufiger hier
#11 erstellt: 04. Mrz 2008, 19:12
Würde sie sofort nehmen, aber ich höre in einer halben stunde, mal eine Steg Qm 310.2 probe! Wenns die nicht wird nehm ich deine!
baschdi85
Stammgast
#12 erstellt: 07. Mrz 2008, 18:41
also,

am wo ende wird wahrsch. ein interessent vorbei kommen und sie mal probehören..

der andere hat erst ab nächstem monat geld.

Preis :

340,- ink. vers. Versand




Mfg
Baschdi
Anabolic_Bass
Ist häufiger hier
#13 erstellt: 07. Mrz 2008, 19:11
Hallo

Bei mir ist es die Steg geworden! Die 1,2 kw hängen jetzt an meinen Ultimo im GG! Klang ist einfach traumhaft!

LG
DUKE_OF_TUBES
Inventar
#14 erstellt: 07. Mrz 2008, 19:22
klop dat ding doch bei ebay rein!
gruss
boris
Koop89
Ist häufiger hier
#15 erstellt: 07. Mrz 2008, 19:50
Was sind das für 4-Kanal Endstufen und was willst du für eine haben??
baschdi85
Stammgast
#16 erstellt: 08. Mrz 2008, 09:58
also die stufen sehen genau so aus wie der monoblock,
bezeichnung ist:
Ultimate T3-4075

hat an 4ohm 4x75wRMS
an 2 ohm 4x120wRMS

gebrückt 2x180wRMS
Dämpfungsfaktor = 205
abgesichert mit 2x40A

THD = 0,04%

sind auch in einem neuwertigen zustand, habe 2stck!

auch mit blauer Volt und Temp anzeige auf der oberseite

Preis :
1Stck VHB 190 ink. versand

Mfg
Sebastian
Koop89
Ist häufiger hier
#17 erstellt: 08. Mrz 2008, 15:56
Hab die bei ebay für im mom 84,78€ gefunden und die geht nur noch ne Std. Hat auch noch keiner drauf geboten...
http://cgi.ebay.de/U...m?_trksid=p1638.m122
Will dir jetzt nicht den Preis kaputt machen oder so aber ich weiß nicht...
Wie hoch war denn der Neupreis? Hab die sonst nirgends gefunden.
baschdi85
Stammgast
#18 erstellt: 08. Mrz 2008, 17:54
wundert mich,..

hatte mal bei ultimate per mail nachgefragt, nach D-land liefern die leider nicht direkt.
hatte die 4-kanäler von nem händler für zusammen 400euro, ist aber schon 3-4jahre her..
den monoblock hatte ich von jemand anderem gekauft,..der war etwas teurer..

Mfg
Baschdi ...sind ja VHB preise, JL und Rockford gibts in den USA ja auch hinterhergeworfen, vor allem bei dem dollarkurs..
baschdi85
Stammgast
#19 erstellt: 08. Mrz 2008, 21:28
ich habe noch ein paar links gefunden, wer interesse hat kann ja mal bissel lesen..

http://www.canadianc...timate-t3-1000d.html

http://www.240forum.com/showthread.php?t=171

http://www.240forum.com/showthread.php?t=171

The T3-1000D is, as you may have guessed, a class D amplifier. It is rated to produce 1000 watts into a 4ohm load and 1200 watts into a 20hm load. This newly designed amplifier is housed in a large aluminum heat sink with small fins running across the top, with an illuminated Ultimate badge in the center. Along the smooth lower 1/3 of the amp is a pair of digital displays that shine through chromed shields. These displays monitor amplifier voltage and temperature. The heat sink has large aluminum end caps and whole thing is left in a raw lightly brushed aluminum finish.
On the left side of the amp are the inputs and signal adjustments. On the left side are two molex sockets. The furthest to the left is labled 12+V output to power some optional accessories like a capacitor with an LCD power read-out. The six-pin socket can be used with a supplied pigtail harness to feed the amp speaker level signals.
The amplifier has a very industrial theme, thanks to the liberal use of hex-head socket screws. The removable end-caps each have a pair of large screws, the Ultimate logo is held together with eight screws and four more in the displays. I really like the look. Industrial yet contemporary in theme. The amplifier's sensitivity can be adjusted by a gain control that is located beside a pair of input/output RCA jacks. the gain is adjustable between 0.25V-8V beside the gain are three processing controls. First is a three-position subsonic filter switch. you can select 20-30-40hz. But the filter cannot be shut-off. The always on low-pass filter is adjustable between 40hz-200hz finally a bass boost control that will allow you to dial up 18db of additional thump. A six-pin phone jack labled RVC will allow you to connect the supplied remote volume control knob.
Which by itself is unlike most amplifiers on the market. It features a small three digit 70segment LED display. This display shows battery voltage, indicates when the amp is clipping or a fuse has blown or overheated. This is great information to have on tap when brutally punishing your amplifier.
The opposite end of the amp is home to the speakers and power connections. The power connections are absolutly massive and will easily accept 0awg cables. The equally robust speaker connections will accept freshly stripped 8awg. Their are two positive and two negative connections. A dual purpose LED between the terminal blocks indicates the amplifiers status. The chromed Ultimate logo illuminates in blue when the amp is operating and should something go wrong it switches to red to let you know when it's time to investigate.
.....ect.....
Two large 30A relays ensure the amp powers up with nary a squeak from your subwoofers. Worth noting are the switching devices that are clamped to the heat sink at an angle leaning away from the board. This means there is a massive amount of heat sink underneath them to wick away potentially damaging heat.
When connect to a 4ohm load and fed with 12.77volts the amp produced a beefy 1369.0 watts at 1%distortion at a efficiency of 77%. Upping the supply voltage to just under 13.5 volts sent the output power sky-rocketing to 1608while drawing 155A of current. This is very serious power into a 4ohm load. Something that is very hard to find in today's market. Most amplifiers make their power at lower impedances. The factory ratings for a bridged 2 ohm load at 13.8 volts is 2700 watts at 210A.
The industrial design of the T3-1000D will definetly make it attractive to mobil audio enthusists. It produces an incredible amount of power at a 4ohm load at very good effiencty. If you are looking for a solid low frequency producing machine be sure to take a look at the T3-1000D.


Mfg
Baschdi
Anabolic_Bass
Ist häufiger hier
#20 erstellt: 08. Mrz 2008, 22:26
Du hast nochmal pm von mir!
baschdi85
Stammgast
#21 erstellt: 13. Mrz 2008, 18:23
Monoblock ist weg,..

die 4-kanäler sind noch da,..

(2 stck)

Preis pro stck 180euro

oder beide zusammen 345euro

Mfg
Baschdi
baschdi85
Stammgast
#22 erstellt: 23. Mrz 2008, 22:00
update:

4-kanal endstufe mit 4x75wRMS an 4ohm!
einzeln 170 euro stck

oder beide zusammen 320euro

ink versand!



Mfg
Baschdi
Suche:
Das könnte Dich auch interessieren:
Macrom M1A.1000D
tobilly am 11.02.2006  –  Letzte Antwort am 14.02.2006  –  3 Beiträge
Mac Audio Fearless 1000D analoger Monoblock
speedcore am 13.02.2010  –  Letzte Antwort am 28.02.2010  –  2 Beiträge
Verkaufe Ultimate T3 4075 4Kanal Endstufe TOP!
baschdi85 am 06.01.2012  –  Letzte Antwort am 19.02.2012  –  6 Beiträge
Kicker ZX2500.1 Monoblock
killmaster am 27.12.2009  –  Letzte Antwort am 30.12.2009  –  2 Beiträge
SYNTEX-1000D Monoblock 1x 1300 rms Monacor Carpower
minki42 am 04.02.2008  –  Letzte Antwort am 06.02.2008  –  8 Beiträge
2x Ampire MX1 Monoblock (1kw an 2Ohm)
Kiela am 15.01.2012  –  Letzte Antwort am 02.02.2012  –  3 Beiträge
Emphaser Xtreme T3 15" und Emphaser Xtreme T3 12" - spotbillig
onkelnorf am 25.06.2006  –  Letzte Antwort am 13.07.2006  –  15 Beiträge
DLS 1000D Verstärker
Sonic3006 am 29.08.2008  –  Letzte Antwort am 09.11.2008  –  8 Beiträge
Hifonics XX-Cap 1000D
RamyNili am 27.08.2012  –  Letzte Antwort am 31.08.2012  –  2 Beiträge
emphaser t3
deltatuning am 05.10.2007  –  Letzte Antwort am 13.10.2007  –  2 Beiträge
Foren Archiv

Anzeige

Produkte in diesem Thread Widget schließen

Aktuelle Aktion

Partner Widget schließen

  • beyerdynamic Logo
  • DALI Logo
  • SAMSUNG Logo
  • TCL Logo

Forumsstatistik Widget schließen

  • Registrierte Mitglieder925.509 ( Heute: 8 )
  • Neuestes MitgliedNicontma
  • Gesamtzahl an Themen1.550.285
  • Gesamtzahl an Beiträgen21.520.930

Hersteller in diesem Thread Widget schließen